Circutor TR16 Series Uživatelský manuál Strana 2
- Strana / 2
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
5.4.2 Sub-slave devices
For communications systems with slaves and sub-slaves (DIAGRAM B. Connection
diagram of the RS-485 slave and sub-slave communications bus), the communica-
tions of the devices marked as sub-slave (A1
2
, A2
2
,,, A32
2
... A1
16
, A2
16
,,, A32
16
) must
have different settings and a node numbering system in order.
The slave nodes (A1, A2 ... A32 ), the same as specied in the previous section, can
be numbered from peripheral 1 to 255 (from 01 to FF in hexadecimal). On the other
hand, the sub-slave nodes of each of the communications buses, must be numbe-
red from 2 to 16 (from 02 to 10 in hexadecimal), and consecutively in each of their
related buses. The slave devices cannot detect the presence of sub-slave devices
with node numbers above 16 (10 in hexadecimal).
Equip-
ment:
Switch 3
Decimal
Node
A1 ON 01
The numbering of the node numbers may
vary between 1 and 255 (from 01 to FF
in hexadecimal). Under no circumstances
may they be duplicated, and they need
not be assigned in a logical or sequential
order.
A1
2
OFF 02 The numbering of the node numbers
may vary between 2 and 16 (from 02 to
10 in hexadecimal) and must be sequen-
tial, without leaving any node numbers
unassigned.
... OFF --
A1
16
OFF 16
IMPORTANT!
If new sub-slaves are added, the slave device must be reset
(leading bus: A1, A2 ... A32 ). For example, if device A2
3
is added,
device A2 must be reset.
This operation is required so that the leading element performs a scan of the entire
communications bus an implements all the information from its sub-slave devices
in its memory map.
5.5 Analogue input and temperature probe
The TR16-RS485 is equipped with an analogue input to connect a probe or an
industrial sensor. The analogue input behaves in a linear manner, delivering by
transmission the analogue measurement in resolution dots (from 0 to 1024 dots).
The communications master is responsible for converting the said dots to physical
values that the user can understand.
Moreover, the equipment has an input for the connection of a Pt100 or Pt1000 type
temperature probe. To connect one or the other type of probe (Pt100 or Pt1000),
it must be selected by using the fourth switch located on the front panel. Once the
switch has been set, the equipment sends the temperature value in degrees centi-
grade by communication.
Temperature probe Switch 4
Pt100 ON
Pt1000 OFF
5.6 Modbus protocol
The TR16-RS485 peripheral uses the MODBUS© protocol. Within the MODBUS©
protocol, the RTU (Remote Terminal Unit) mode is used; every 8-bits per byte in a
message contains two 4-bit hexadecimal characters.
The format for each byte in RTU mode is:
Code
8 binary bits, hexadecimal 0-9, A-F
2 hexadecimal characters contained in each 8-bit eld
of the message.
Bits per byte 8 data bits
Check-Error eld CRC (Cyclical Redundancy Check) type
Implemented Modbus functions:
Functions 03
and 04
Function used for reading the parameters measured by the
TR16-RS485. All the electric parameters are 16 bit words,
so that to request each parameter one Word (2 bytes – XX)
is needed.
5.6.1 Modbus/RTU® memory map
This table shows the Modbus addresses of the conventional slave device. In the
successive tables (from module 2 on), the memory addresses are displayed for the
sub-slave devices, if these are connected.
Description Abbreviation Symbol Address Unit
Input current 1 M1-MLC1 I 1 0000 A x 100
Input current 2 M1-MLC2 I 2 0001 A x 100
Input current 3 M1-MLC3 I 3 0002 A x 100
Input current 4 M1-MLC4 I 4 0003 A x 100
Input current 5 M1-MLC5 I 5 0004 A x 100
Input current 6 M1-MLC6 I 6 0005 A x 100
Input current 7 M1-MLC7 I 7 0006 A x 100
Input current 8 M1-MLC8 I 8 0007 A x 100
Input current 9 M1-MLC9 I 9 0008 A x 100
Input current 10 M1-MLC10 I 10 0009 A x 100
Input current 11 M1-MLC11 I 11 000A A x 100
Input current 12 M1-MLC12 I 12 000B A x 100
Input current 13 M1-MLC13 I 13 000C A x 100
Input current 14 M1-MLC14 I 14 000D A x 100
Input current 15 M1-MLC15 I 15 000E A x 100
Input current 16 M1-MLC16 I 16 000F A x 100
Differential Voltage M1-VDG Vd 0010 V x 10
Pt100/Pt1000
temperature
M1-TEMP Pt100/Pt1000 0011 ºC
Analogue input M1-ANAL 0012 Dots
Digital inputs M1-DIG 0013 0 / 1
Not used 0014
Peripheral number M1-PERIPH 0015
In the successive tables (from sub-slave 2 on), the initial addresses of the modules
are shown, taking into account that they all have the same distribution available to
the leading bus device.
Module Addresses Module Addresses
2 0016 to 002B 10 00C6 to 00DB
3 002C to 0041 11 00DC to 00F1
4 0042 to 0057 12 00F2 to 0107
5 0058 to 006D 13 0108 to 011D
6 006E to 0083 14 011E to 0133
7 0084 to 0099 15 0134 to 0149
8 009A to 00AF 16 014A to 015F
9 00B0 to 00C5
Examples of the memory addresses of some of the sub-slave devices, if these are
connected.
Module 2 Address UDS Module 3 Address UDS
M2-MLC1 0016 A x 100 M3-MLC1 002C A x 100
M2-MLC2 0017 A x 100 M3-MLC2 002D A x 100
M2-MLC3 0018 A x 100 M3-MLC3 002E A x 100
M2-MLC4 0019 A x 100 M3-MLC4 002F A x 100
M2-MLC5 001A A x 100 M3-MLC5 0030 A x 100
M2-MLC6 001B A x 100 M3-MLC6 0031 A x 100
M2-MLC7 001C A x 100 M3-MLC7 0032 A x 100
M2-MLC8 001D A x 100 M3-MLC8 0033 A x 100
M2-MLC9 001E A x 100 M3-MLC9 0034 A x 100
M2-MLC10 001F A x 100 M3-MLC10 0035 A x 100
M2-MLC11 0020 A x 100 M3-MLC11 0036 A x 100
M2-MLC12 0021 A x 100 M3-MLC12 0037 A x 100
M2-MLC13 0022 A x 100 M3-MLC13 0038 A x 100
M2-MLC14 0023 A x 100 M3-MLC14 0039 A x 100
M2-MLC15 0024 A x 100 M3-MLC15 003A A x 100
M2-MLC16 0025 A x 100 M3-MLC16 003B A x 100
M2-VDG 0026 V x 10 M3-VDG 003C V x 10
M2-TEMP 0027 ºC M3-TEMP 003D ºC
M2-ANAL 0028 Dots M3-ANAL 003E Dots
M2-DIG 0029 0 / 1 M3-DIG 003F 0 / 1
Not used 002A 0040
M2-PERIPH 002B M3-PERIPH 0041
5.6.2 Reading of the status of the digital inputs (DIG)
The DIG variable, like the rest of the electric variables, is a record (1 word = 2 bytes),
in other words, in hexadecimal it would be 0xFFFF. The inputs go from 1 to 3 and
these represent the 3 lower weight bytes:
HIGHEST WEIGHT BYTES LOWEST WEIGHT BYTES
7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0
0 0 0 0 0 0 0 0 0 0 0 0 0 I3 I2 I1
To know the Modbus memory addresses, refer to section 05.06.01 Memory map.
The value of each input determines if it is activated (1) or deactivated (0).
Example 1 (in master device):
TX NP 0400090001 CRC
Input activated 3
By communication
INP=0x0004 Hexadecimal
0000000000000100 Binary
Example 2 (in master device):
TX NP 0400090001 CRC
Input activated 2 and 3
By communication
INP=0x0006 Hexadecimal
0000000000000110 Binary
5.6.3 Reading the peripheral number
The PERIPH variable, like the rest of the electric variables, is a record (1 word = 2
bytes), in other words, in hexadecimal it would be 0xFFFF. This record refers to the
peripheral number associated by using the front panel on the equipment, for each
of the slave and sub-slave devices.
5.6.4 Number and listing of sub-slave devices connected
Number of sub-slave devices: There is a Modbus record (0834), which indicates
the number of sub-slave devices connected to the communications master (see in
DIAGRAM B, devices, A2 ... A16). Said variable solely returns the numeric value in
hexadecimal, reporting the number of nodes connected to the device through the
master communications port (if it is used).
Example 1:
TX NP 0408340008 CRC
RX NP 0402 0006 CRC
Number of slaves 6
By communication RX = 0x0006 Hexadecimal
Decimal conversion 6 Decimal
Listing of sub-slave devices: As opposed to the number, the listing of sub-slave
elements connected to a master device, reports one by one, the peripheral numbers
connected to the said master device (record 07D0).
Example 1:
TX NP 0407D0000F CRC
RX NP 0420 02 03 04 05 06 00 00 00 00 00 00 00 00 00 00 00 CRC
Listing of slaves 02, 03, 04, 05, 06 Hexadecimal
Decimal conversion 02, 03, 04, 05, 06 Decimal
6. DIMENSIONS
106.0
6/1
Multi-purpose clips for
x
y
x
y
y
99.8
30.2
60.6
(pitch of wall mounting
holes in din rail clips)
160.0
9/1
113.8
56.9
99.8
y
160
45
+12V
S5/S1
GND
GND
S6/S2
S7/S3
S8/S4
+15V -15V O/P
40.0
15
.
5
22.
5
25.0
12.
5
10.0ø
7. TECHNICAL ASSISTANCE SERVICE
If you have any doubts about the operation of the equipment or any malfunction,
please contact the technical assistance service at CIRCUTOR SA
CIRCUTOR, SA - Technical Assistance Service
Vial Sant Jordi, s/n - 08232 Viladecavalls (Barcelona) SPAIN
Tel.: 902 449 459 (Spain) - +34 93 745 29 00
email: sat@circutor.es
DIAGRAM A - Connection diagram of the RS-485 communications bus with slave devices (conventional bus)
DIAGRAM B - Connection diagram of the RS-485 communications bus with slave and sub-slave devices
SWITCH ON SWITCH OFF
M98234101-03-15A
1
2
Související produkty a manuály pro Měřící nástroje Circutor TR16 Series
(124 stránky)
(2 stránky)
(2 stránky)
(2 stránky)
(124 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.050 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce