Circutor CPM (Available until stocks) Uživatelský manuál

Procházejte online nebo si stáhněte Uživatelský manuál pro Měřící nástroje Circutor CPM (Available until stocks). CIRCUTOR CPM (Available until stocks) User Manual Uživatelská příručka

  • Stažení
  • Přidat do mých příruček
  • Tisk

Shrnutí obsahu

Strany 1 - INSTRUCTION MANUAL

MULTIMETER CURRENT CLAMP CPM (Code: M80430) INSTRUCTION MANUAL ( M98111201-03-10A )  CIRCUTOR S.A.

Strany 2 - 1.1.- Description

--------- MULTIMETER CURRENT CLAMP CPM -------- PG No. 9 - Symbols: The analyzer is protected by double or reinforced insulation. Caution

Strany 3 - -------- PG No. 2

--------- MULTIMETER CURRENT CLAMP CPM -------- PG No. 10 - 2.2.- Special precautions  This equipment can be used for Overvoltage Catego

Strany 4 - 1.2.- Specifications

--------- MULTIMETER CURRENT CLAMP CPM -------- PG No. 11 - 3.- INSTRUCTIONS FOR USE 3.1.- Description of controls and elements A B

Strany 5 - -------- PG No. 4

--------- MULTIMETER CURRENT CLAMP CPM -------- PG No. 12 - [1] Rotary function switch Analyzer off DC voltage measurement, range 6

Strany 6 - -------- PG No. 5

--------- MULTIMETER CURRENT CLAMP CPM -------- PG No. 13 - [3] V input terminal for AC/DC voltage measurement [4] COM common input term

Strany 7 - -------- PG No. 6

--------- MULTIMETER CURRENT CLAMP CPM -------- PG No. 14 - 3.2.- Use ATTENTION When the value to be measured is unknown always place t

Strany 8 - -------- PG No. 7

--------- MULTIMETER CURRENT CLAMP CPM -------- PG No. 15 - 3.2.2.- Current measurement 1. Set the rotary switch [1] to the desired higher

Strany 9 - 2.1.- General

--------- MULTIMETER CURRENT CLAMP CPM -------- PG No. 16 - 3.2.4.- Frequency measurement 1. Set the rotary switch [1] to the Hz position.

Strany 10 - -------- PG No. 9

--------- MULTIMETER CURRENT CLAMP CPM -------- PG No. 17 - 3.2.6.- Diode test 1. Connect the black test probe to the COM terminal [4] an

Strany 11 - 2.2.- Special precautions

--------- MULTIMETER CURRENT CLAMP CPM -------- PG No. 18 - 4.- MAINTENANCE Attention : Disconnect the test probes before changing the

Strany 12 - 3.- INSTRUCTIONS FOR USE

--------- MULTIMETER CURRENT CLAMP CPM -------- PG No. 1 - CPM ANALYZER INDEX page no. SAFETY NOTES Before using the equip

Strany 13 - -------- PG No. 12

--------- MULTIMETER CURRENT CLAMP CPM -------- PG No. 19 - Caution : Do not use aromatic hydrocarbons or chlorinated solvents for clea

Strany 14 - -------- PG No. 13

--------- MULTIMETER CURRENT CLAMP CPM -------- PG No. 2 - The analyzer is powered by a 9 V battery. Its design and its double insulation m

Strany 15 - 3.2.- Use

--------- MULTIMETER CURRENT CLAMP CPM -------- PG No. 3 - 1.2.- Specifications Display 3 ½ digit LCD display with a maximum reading of

Strany 16 - -------- PG No. 15

--------- MULTIMETER CURRENT CLAMP CPM -------- PG No. 4 - Power Supply 9 V, IEC 6F22 battery. Battery life Typically 200 hours for a zi

Strany 17 - -------- PG No. 16

--------- MULTIMETER CURRENT CLAMP CPM -------- PG No. 5 - DC Voltage Range Accuracy Input impedance Overload protection 600 V ±

Strany 18 - -------- PG No. 17

--------- MULTIMETER CURRENT CLAMP CPM -------- PG No. 6 - Continuity Sound alarm Overload protection Less than 30Ω in the range of 2

Strany 19 - 4.2.- Cleaning and storage

--------- MULTIMETER CURRENT CLAMP CPM -------- PG No. 7 - 700 A AC Max. during 1 minute.

Strany 20 - 4.3.- TECHNICAL SERVICE

--------- MULTIMETER CURRENT CLAMP CPM -------- PG No. 8 - 2.- SAFETY REQUIREMENTS 2.1.- General  This equipment can be used in envir

Komentáře k této Příručce

Žádné komentáře